Introduction:

Installing an immobiliser on your car is a great way to enhance the security of your vehicle and protect it from theft. An immobiliser is a robust electronic security device that disables a car’s engine if it is not started using a specific key or transponder. This comprehensive guide will take you through installing an immobiliser on your car, so you can feel confident in securing your vehicle. Ghost 2 immobiliser installation provides a system that protects your vehicle from key-cloning, theft, and hacking via a unique pin code that you can choose to save your car.

Before you Start:

• Gather the necessary tools and equipment: To install an immobiliser, you will need a range of devices, including a screwdriver, pliers, wire cutters, and electrical tape. You will also need the immobiliser kit, which includes the control unit, wiring harness, and transponder.
• Familiarise yourself with the wiring diagram: Before starting the installation process, it is essential to familiarise yourself with your car’s wiring diagram. This diagram will help you to understand the different wiring connections and make it easier for you to install the immobiliser areas 
• suitable location for the control unit: The immobiliser’s control unit is the main component and needs to be installed in a place that is easily accessible and protected from damage. Commonly, it is installed under the dashboard, in the glove box, or under the seat.

Here Are Six Steps You Can Follow to Install an Immobiliser in Your Car:

Step 1: Disconnect the Battery

The first step in installing a Ghost 2 Immobiliser is disconnecting the battery. This is important because it will prevent electrical damage to the car’s wiring and components during installation. To locate the battery and remove the negative terminal.

Step 2: Locate the Starter Motor and Ignition Switch

The next step is to find the starter motor and ignition switch. The starter motor is installed to start the car engine, while the ignition switch provides power to the starter motor. Once you have found these two components, you will need to identify the positive and negative wires connected to them; after getting the ignition switch off, install the Ghost 2 Immobiliser carefully. 

Step 3: Connect the Immobiliser Wiring Harness

Next, you will need to connect the Ghost 2 Immobiliser wiring harness to the starter motor and ignition switch. The wiring harness will have specific connections for each of these components. Follow the wiring diagram to ensure that the links are made correctly.

Step 4: Install the Control Unit

Once the wiring connections have been made, you can install the control unit of the Ghost 2 Immobiliser. Choose a suitable location for the control unit, and secure it using screws or bolts. The control unit should be easily accessible but also protected from damage.

Step 5: Program the Transponder

The final step is to program the transponder. This is a small device typically attached to your car’s key. The transponder is programmed to send a signal to the immobiliser’s control unit, allowing the engine to start when the key is used.

To program the transponder, you must follow the instructions immobiliser kit. The process will vary depending on your immobiliser, so it is essential to follow the instructions carefully.

Step 6: Test the Immobiliser

Once the installation is complete, it is essential to test the Ghost 2 Immobiliser to ensure it is working correctly. To do this, reconnect the battery and try starting the engine using the transponder key. If the engine starts, the immobiliser is working correctly.

Average Cost of Immobiliser in the Market

The Ghost 2 Immobiliser is a high-tech device to secure vehicles and protect them from theft. The cost of this device varies depending on the model and features, but it typically ranges from around £200 to £500. The device uses advanced encryption algorithms to prevent unauthorised access to the vehicle, and it can be controlled remotely via a smartphone app. The Ghost 2 Immobiliser can also be configured to provide real-time updates on the vehicle’s status, making it easy to monitor its security at all times.

In addition to the starting cost of the device, ongoing costs may be associated, such as subscription fees for access to the smartphone app or professional installation. However, these costs are usually outweighed by the peace of mind when you feel relax.

Conclusion:

Installing a Ghost 2 Immobiliser on your car is an intelligent move to enhance your vehicle’s security. This process is easy and straightforward, requiring only essential tools and knowledge. The result is a highly effective protect solution that will give you peace of mind regarding your car’s safety. Whether you are a seasoned car owner or just starting out, following these steps will ensure a successful installation.